litter robot keeps saying full

clayton-bonapart-oldakowski July 30, 2022 full , litter , robot , saying Comment

How to resolve the issue depends on the flashing sequence. A slow yellow flashing light one flash per second.

We Bought A Litter Robot Was It Worth It Three Chatty Cats

Make sure any dirt or obstacles is not blocking the sensor.

. LR3 Blue Light Blinking. You will need a 3mm hex wrench. Yellow light turns off blue light remains lit.

Posted on 17092014 by jgendron in Domestic Litter-Robot. Your Litter-Robot may keep saying its full due to issues regarding the DFI lenses. Dont worry the fix is stupidly simple takes 5 minutes this just looks like a lot of steps dont worry.

We have also been told that dryer sheets below the drawer liner helps keep odor down. Unplug your unit remove the globe and bonnet where applicable and locate the black spur gear on the right side control. Both blue AND yellow lights are now on.

To abort the clean cycle press reset or empty. Using your 3mm hex wrench tighten the screw by turning it to the right. There are basically 5 reasons why your Litter Robot 3 self-cleaning litter box smells.

NEWER MODEL USERS NEED TO REMOVE THE BONNET. Hold the Cycle button for 5 seconds. When you look at the waste opening on the base of the unit youll also see the DFI lenses which need to be clean at all times.

LR 3 Getting Started with your Litter-Robot 3. Now if the sensors are clean there is no dust in the drawer. Press the Reset button twice.

If your Litter-Robot is experiencing a free or loose spinning gear and no globe movement it sounds like the set screw has come loose. Litter-Robot 3 Connect App Connect. WASH THE LITTER ROBOTS GLOBE.

When its tight enough and doesnt move anymore you can place the globe back on the base turn on the power and press Cycle. Press any button to put the unit on pause. Disassemble the base carefully as there are wires connected to the control unit and to the pressure sensor in the foot of the base.

If its up too high it can block the DFI lens making the Litter-Robot think its full. Remove the Receptacle Drawer. On the other hand a blinking yellow light signals a problem.

I got a new router WiFi network. LOCATE AND PRESS THE LITTER ROBOTS EMPTY BUTTON. Once aligned turn off the power and unplug your Litter-Robot.

Hold the Cycle button for 5 seconds. To unpause the unit press the cycle button. How do I reconnect.

DEAL WITH ANY EXCESS LITTER. PLACE A NEW TRASH BAG INTO THE. If theyre not clean and debris has accumulated the Litter-Robot may keep.

Lack of frequency in cleaning the unit cleaning only the globe not changing the carbon filter often the base seals have worn out wrong diet or possible medical condition with your cat. Below are the instructions to tighten the set screw. I didnt want to mention the type of cat litter on this list.

Activate the cat sensor by pressing on the globe just above the entrance in a forward and. I hope this helps. How to fix the blinking blue light on the litter robot open air that says the tray is full when its not.

Domestic Litter-Robot Robot Litter Robot Pet Care. Why Does My Litter-Robot Keep Saying Its Full. Litter-Robot 3 Support Articles Litter-Robot 2 Support Articles Getting started with your Litter-Robot 2 Getting started with your Litter-Robot 3 Litter-Robot 3 Litter-Robot 2.

Plug the unit back in allow it to complete the start-up cycle and follow the steps below. The flat side of the shaft should be facing you. Litter-Robot II Basic Troubleshooting Guide.

Press the cycle button Removing the waste drawer. If the blue light is blinking now the drawer is somehow removed. LET THE GLOBE DRY.

Then press the Reset button. Other users have mixed baking soda in with their litter andor liners. EMPTY AND WIPE DOWN THE WASTE DRAWER.

Make sure the waste drawer liner bag is fully inserted in the waste drawer.

Litter Robot Troubleshooting Fixing Common Litter Robot 3 Issues Floppycats Litter Robot Litter Cat Litter